IEC Motor Frame Sizes Explained: 63 to 200 Frame Dimension Chart
Key Takeaway: An IEC frame number is the shaft centre height in millimetres; the S, M or L suffix is the frame length. Frames 63 to 200L cover roughly 0.18 kW to 30 kW at 4 poles. Match shaft height, shaft diameter and foot-hole or flange dimensions before ordering a replacement motor.
What a Frame Size Tells You
The frame size on a motor nameplate is a dimensional standard, not a power rating. It fixes the mounting dimensions of the motor so that a unit from one manufacturer can physically replace a unit from another. The dimensions are defined in IEC 60072-1 and adopted in India under IS 1231 (foot-mounted motors) and IS 2223 (flange-mounted motors).
The number itself is the shaft centre height in millimetres, measured from the underside of the feet to the centre of the shaft. A 132 frame motor has its shaft centre 132 mm above the mounting surface.
The Suffix Letters: S, M and L
The letter after the number indicates the length of the frame: S (short), M (medium) or L (long). Two motors of the same frame number share the same shaft height and the same side-to-side foot spacing, but the front-to-back foot spacing increases with frame length. A 90S and a 90L are therefore not always interchangeable on an existing base plate without re-drilling.
Frame Dimension Chart (Foot-Mounted, B3)
H is the shaft centre height, D the shaft diameter, A the distance between foot-hole centres across the motor and B the distance between foot-hole centres along the motor. Output is the rating commonly assigned to a 4-pole (1500 rpm synchronous) motor in that frame.
| Frame | H (mm) | Shaft D (mm) | Foot holes A × B (mm) | Typical 4-pole output |
|---|---|---|---|---|
| 63 | 63 | 11 | 100 × 80 | 0.18 kW (0.25 HP) |
| 71 | 71 | 14 | 112 × 90 | 0.37 kW (0.5 HP) |
| 80 | 80 | 19 | 125 × 100 | 0.75 kW (1 HP) |
| 90S | 90 | 24 | 140 × 100 | 1.1 kW (1.5 HP) |
| 90L | 90 | 24 | 140 × 125 | 1.5 kW (2 HP) |
| 100L | 100 | 28 | 160 × 140 | 2.2 kW (3 HP) |
| 112M | 112 | 28 | 190 × 140 | 3.7 kW (5 HP) |
| 132S | 132 | 38 | 216 × 140 | 5.5 kW (7.5 HP) |
| 132M | 132 | 38 | 216 × 178 | 7.5 kW (10 HP) |
| 160M | 160 | 42 | 254 × 210 | 11 kW (15 HP) |
| 160L | 160 | 42 | 254 × 254 | 15 kW (20 HP) |
| 180M | 180 | 48 | 279 × 241 | 18.5 kW (25 HP) |
| 180L | 180 | 48 | 279 × 279 | 22 kW (30 HP) |
| 200L | 200 | 55 | 318 × 305 | 30 kW (40 HP) |
The output column is a guide only. The same frame carries a different rating at 2, 6 or 8 poles, and higher efficiency classes sometimes move a rating into the next frame. Always confirm the frame against the manufacturer's datasheet before ordering a replacement.
Mounting Codes on the Nameplate
- B3: Foot-mounted, horizontal shaft.
- B5: Flange-mounted with clearance holes in a large flange. An 80 or 90 frame B5 motor uses a 165 mm pitch circle (FF165).
- B14: Face-mounted with tapped holes in a small face. An 80 frame B14 motor uses a 100 mm pitch circle (FT100).
- B35: Foot and flange combined.
- V1: Flange-mounted, vertical, shaft pointing down.
Measuring an Unmarked Motor for Replacement
- Measure from the base of the feet to the shaft centre. This gives the frame number.
- Measure the shaft diameter and the usable shaft length.
- Measure the foot-hole centres across (A) and along (B) the motor to identify S, M or L.
- For flange motors, measure the pitch circle diameter of the bolt holes and note whether they are clearance or tapped holes.
- Record the nameplate kW, speed, voltage and duty, then match all of it to the replacement's datasheet.
For help matching a frame to a foot, flange or face-mounted motor, send the measurements to the Sun Star Motors™ team.